Что-то 3й день молчит Мартин. Я ему и ответ с завода переслал, но... пока от него ответа нет. Отморозился что-ль... Ежели до завтра не ответит, придется применять разборки через PayPal.
Кстати, а кто может порекомендовать в Москве сварщиков/лудильщиков или как их там... чтоб, ежели что, котел заварить/запаять ?
Мне кажется в вашем случае единственный выход - замена бойлера. Обычная пайка не пойдет, большой бойлер обладает высокой теплопроводностью. Остальные методы пайки не тривиальны и используют сильные химические реагенты (на основе токсичных металлов - серебра, кадмия или свинца), особенно с учетом контакта с пищевой средой. Можно газовой гарелкой попробовать но тут только специалист может ответ дать.
Требуйте замену бойлера, тем более производитесь прямо на это указал.
Как там сделано: рама есть но она ровно под кубиком машины. Над рамой основной вес. В передняя часть, на которую поддон ставится, приварена к этой раме под кубиком. А так как основной вес приходится на сам кубик (где бойлер), а ножки передние под поддоном, то место соединения надо бы сделать более серьезно. Иначе имеем то, что имеем.
могу отфотографировать, как это сделано у моей Маджики, но не совсем понял л чем речь! месте сочленения каркаса на который ставится поддон и корпуса?
Насколько я разбираюсь медь не варят, только пайка.
В атмосфере аргона варится все. и медь и аллюминий и титан. В принципе можно снять бойлер, прогреть его на газу (в духовке) до 210-220 градусов и запаять оловом.
Вообще-то "обычный оловянный припой" чаще всего является обычным оловянно-свинцовым припоем, так что не советую. Серебряные припои часто содержат кадмий. Надо искать что-то пищевое.
Место для пайки удобное.Покупаете флюс,припой проволоку в любом радиомагазине.В любом гипермаркете газовый балон -[ссылка]- и насадку к нему -[ссылка]- .Чистите место свища,мажете флюсом,греете,прикасаетесь проволокой к месту свища----она плавится и растекается.Минут на 10 делов. Бюджет рублей 150 -250
alextar: уже новую версию? в Москве, похоже, посмотреть негде?
Не знаю, насколько новую, на вид вроде нулячие, на модели не обратил внимания, все равно пока покупать не собираюсь. Из граненой даже эспрессо попробовал.
Ростислав. написал(а) ...
alextar: на салютной? Что-то интересное увидели?
Да, на Салютной. Выставка – левая. Из оборудования – только Голденбар, Либерти и Дом Кофе. Куча какого-то непонятного итальянского кофе, даже не стал пробовать, так как заказал Gene Cafe. Собственно, надеялся поговорить с нашими обжарщиками на предмет закупки зеленки в розницу, а никого не было.
alextar: уже новую версию? в Москве, похоже, посмотреть негде?
Новые версия Рокетов ЭВО (2012) отличается от старых: 1. черным табло на манометрах 2. тем, что бойлер обернули в какую-то теплоизоляцию 3. Внутри что-то чуть иначе развели.
Так как п.п. 1-2 можно представить и так, а оптимизация внутренней разводки тема такая, что главное, чтобы акуратно все сделали, то... версию 2012 можно и не смотреть, а если есть желание, глянуть у мну 2011, а остальное дофантазировать
Меня там не было , я про кофе и машину спросил. Во Львов лучше приезжайте, там и Марзокки есть (в Свите кавы) и кофе получше (на чемпах).
я еще в Кентавре пил кофе с GB/5, а где-то еще во Львове Марзоки стоят?
Nikolay_B написал(а) ...
Новые версия Рокетов ЭВО (2012) отличается от старых: 1. черным табло на манометрах 2. тем, что бойлер обернули в какую-то теплоизоляцию 3. Внутри что-то чуть иначе развели.
хорошо, что у Вас бойлер без "утепления", проще было идентифицировать откуда дует! хотя если будут менять, то может новый вышлют? а манометры они по моему постоянно меняют, помню Мартин показывал на какой-то ракете якобы "попроще" на какой-то якобы "получше"...
Что-то Мартин мне не отвечает уже 4 дня Придется кляузничать через PayPal
конечно! думаю, это должно его заставить зашевелиться! как уже писали, его вина очевидная и однозначная - не проверил аппарат перед отсылкой в другую страну с геморами типа таможни и т. п.
Зря я на Мартина балон катил. Получил от него ответ.
We organized everything so far to sort out the problem. What we'd like you to do is to send us the espresso machine back.
It is a material fault of the boiler which we (Rocket) haven't had so far. We will change the machine into a new one. For customs reasons it is better you choose the preferred shipping company and send it to our warehouse. Due to the fact that we will pay for the shipping please put the invoice (shipping costs) of shipping into the parcel.
Please tell us when you send the machine (in original parcel, well softened) back to us. Everything will be covered from our site. The only effort you have is to help us to get the Machine a.s.a.p. to our warehouse. You will receive a proforma invoice and a delivery note to pack by.
We apologize for the inconvenience so far and assure you the best service possible to get the new machine to you. Thank you very much for your support.
Nikolay_B: ну, это действительно европейский подход к сервису... жалко, конечно что не все гладко сразу, но это самый оптимальный исход сложившейся ситуации, как мне кажется
Действительно... Сервис... Сейчас даже жалко станет продавца Когда он увидит счет емс... Николай, поздравляю с удачным решением проблемы. Только попросите следующую машину проверить на месте
Действительно... Сервис... Сейчас даже жалко станет продавца Когда он увидит счет емс... Николай, поздравляю с удачным решением проблемы. Только попросите следующую машину проверить на месте
EMS, как я понял, не умеет для физ лиц отправлять с оплатой получателем: Услуга «оплата получателем» оказывается только контрактным клиентам по безналичному расчету.. Так что мои 200 с лишним евро потратятся на данную итерацию Попросить что ль компенсировать какими-нить аксекссуарами типа доп. чашек...
водитель запаяет бойлер и будет варить "настоящий эКспрессо"!
Nikolay_B: по поводу возмещения стоимости доставки в Германию, с приведенной цитаты Мартина, я так понял что он просил вложить инвойс в упаковку с машиной (для отчета видимо или чтоб срубить денег с Рокетовцев), а не отсылать за их счет. другой вопрос как он потом эти деньги возместит? может действительно каким-то ликвидным товаром?
Тут еще один вопрос есть, как оказалось... EMS в Германию принимает посылки весом не более 30кг. Мотивирует это тем, что немцы бОльший вес у них не принимают. Несмотря на то, что Мартин все, что можно, вытащил из кофемашины при отправке (поддон, портафильтры, даже бачок для воды), вес посылки был 30,4 кг. Да, у него там были не только пакетики с воздухом проложены, но и чуток картонок, которые я заменю на надыбанный у друзей пенополиуретан, но все равно что-то я сомневаюсь, что в 30кг уложусь. Почта России вообще принимает посылки до 20кг. Ценник у TNT и прочих DHL слегка зверский - порядка 25 тыс. руб (600-650 EUR). Если EMS откажется принимать мое отправление, будет весело
Кофемашина:Rocket Cellini Evo v2, La Pavoni EL
Кофемолка:Promac MD 74 AT, Mazzer Mini E, Hario mini
Ростер:Gene Cafe, I-Roast2
Др. оборудование: аэропресс, Кемекс, Харио V60, электронная турка, френч-пресс
Nikolay_B: а какой конторой он Вам прислал машинку мне тут одни друзья предлагают прислать такую же машинку за 250-300 ойро через UPS, у Вас как я понимаю вышло 70?
Nikolay_B: а какой конторой он Вам прислал машинку мне тут одни друзья предлагают прислать такую же машинку за 250-300 ойро через UPS, у Вас как я понимаю вышло 70?
Обычным DHL/Deutsche Post. У нас забирал в своем почтовом отделении.
Nikolay_B: на сайте дчл посылки для раши возможны только до 20кг, интересно как ему удалось пропихнуть Вашу машинку 70 для парсела в 30кг какая-то невероятная цена а страховка на какую сумму?
Nikolay_B: на сайте дчл посылки для раши возможны только до 20кг, интересно как ему удалось пропихнуть Вашу машинку 70 для парсела в 30кг какая-то невероятная цена а страховка на какую сумму?
называлось это Premium Versand DHL-Russland. Сумма страховки непонятна. На квитке DeutschePost'а стоит Bruttogewicht 20,000 kg, который в россии сразу стал 30,4
Nikolay_B: старик Хоттабыч, да и только, нахрена только он бачок для воды из машинки вытаскивал, с его способностями он сможет слать девайсы с неограниченным весом, похоже
Nikolay_B: на сайте дчл посылки для раши возможны только до 20кг, интересно как ему удалось пропихнуть Вашу машинку 70 для парсела в 30кг какая-то невероятная цена а страховка на какую сумму?
Мне сейчас маджика идет 24 кг, стоимость доставки меньше 70 евро. и на дом привозят, я уже так заказывал. stoll-espresso.de. у них одна цена доставки на все выше 2кг.
Принял у меня EMS посылку. Долго я с машинкой мучался (частично слил воду из бойлера, заменил в упаковке картон на более легкий пенополеуретан), но результат достойный - вместо веса 30,44кг, который был у Мартина, получилось 30,1кг Отправка со страхованием обошлась в 9345р (EUR 242,64 по курсу ЦБ РФ).
Сейчас отпишу Мартину номер отправления и его стоимость, посмотрим, что предложит
Nikolay_B: принял с оплатой за счет получателя или как?
Агащазблин, за мой счет, конечно. Они не умеют за границу за счет получателя отправлять. А гемороиться с DHL'ем с его красивыми тарифами, не включащими НДС и топливную надбавку или UPS'ом мне чего-т не хотелось. Возместит мне Мартин как-нить/чем-нить - хорошо, не возместит - ну и ладно, не обанкрочусь из-за этой суммы
Многие знают, что я фанат Аэропресс. Поэтому, очень долго откладывал в самый дальний ящик покупку данного устройства. Зачем кому-то нужен клон Аэропресса? Однако, на деле оказалось, хоть эти устройства и похожи, у Дельтер Пресса есть свои особенности. Покупать Дельтер Пресс рекомендую в случае, если уже всё есть. На этом можно было бы закончить статью, но давайте разберемся, почему эта кофеварка не только красивый кусок китайского пластика с австралийским акцентом, но имеет огромный потенциал.
Сейчас разгар отпусков и лета 2019 года, я сижу в кофейне, где-то между Австрией, Венгрией и Чехией, пью колд-брю и решил написать для нашего прекрасного русско-язычного кофейного комьюнити, что я думаю по этому поводу и какие основные два метода заваривания доступны для обычного человека. Тем более, что у Sweet Beans Coffee на складе в Краснодаре появился удивительный PUCKPUCK, который теперь всегда со мной.